Wednesday, June 28th 2017, 5:38am UTC+2

You are not logged in.

  • Login
  • Register

Asadloa

Beginner

Date of registration: May 26th 2017

Posts: 5

1

Friday, June 2nd 2017, 12:47pm

MAC57D5, J-Link, S32 DS

I tried running Free RTOS by Mobiliya for CM4 in MAC57D5 using J-Link, but I have been successful in getting the set up to work. When I debug the RTOS project on S32 I get errors which are prvided down below. At this point, after having tried for so long without getting any help from anywhere, I am desperate. Any help or response otherwise would be greatly appreciated.
Best Regards
Asad Ullah

"SEGGER J-Link GDB Server V6.14h Command Line Version

JLinkARM.dll V6.14h (DLL compiled May 10 2017 18:22:45)

WARNING: Unknown command line parameter -timeout found.
WARNING: Unknown command line parameter 0 found.
-----GDB Server start settings-----
GDBInit file: none
GDB Server Listening port: 2331
SWO raw output listening port: 2332
Terminal I/O port: 2333
Accept remote connection: localhost only
Generate logfile: off
Verify download: on
Init regs on start: on
Silent mode: off
Single run mode: on
Target connection timeout: 0 ms
------J-Link related settings------
J-Link Host interface: USB
J-Link script: none
J-Link settings file: none
------Target related settings------
Target device: MAC57D5
Target interface: SWD
Target interface speed: 1000kHz
Target endian: little

Connecting to J-Link...
J-Link is connected.
Firmware: J-Link V10 compiled Apr 21 2017 10:28:25
Hardware: V10.10
S/N: 260102083
OEM: SEGGER-EDU
Feature(s): FlashBP, GDB
Checking target voltage...
Target voltage: 3.38 V
Listening on TCP/IP port 2331
Connecting to target...Connected to target
Waiting for GDB connection...Connected to 127.0.0.1
Reading all registers
Read 4 bytes @ address 0x00000000 (Data = 0xE59FF004)
Target interface speed set to 1000 kHz
Resetting target
Halting target CPU...
...Target halted (PC = 0x1840494C)
R0 = 00000004, R1 = 00000001, R2 = 00000000, R3 = 00000000
R4 = 00000001, R5 = 3E00026C, R6 = 00000000, R7 = 00000000
R8 = 00000000, R9 = 00000000, R10= 00000000, R11= 00000000
R12= 00000000, R13= 3E0001EC, MSP= 3E0001EC, PSP= 00000000
R14(LR) = 1840494D, R15(PC) = 1840494C
XPSR 61000000, APSR 60000000, EPSR 01000000, IPSR 00000000
CFBP 00000000, CONTROL 00, FAULTMASK 00, BASEPRI 00, PRIMASK 00
Reading all registers
Read 4 bytes @ address 0x1840494C (Data = 0xD0062801)
Select auto target interface speed (2000 kHz)
Flash breakpoints enabled
Semi-hosting enabled (Handle on BKPT)
Semihosting I/O set to TELNET Client
SWO disabled succesfully.
ERROR: Could not detect CPU clock speed. Verification of test code downloaded into RAM failed.

Failed to enable SWO. Could not measure target CPU frequency.
Read 4 bytes @ address 0x1840494C (Data = 0xD0062801)
Downloading 28 bytes @ address 0x18F9C000 - Verify failed
.
.//The statements have been replaced by dots to limit the whole message with in 10000 words.
.
Downloading 4096 bytes @ address 0x1902BAAC - Verify failed
Downloading 4096 bytes @ address 0x1902CAAC - Verify failed
Downloading 4096 bytes @ address 0x1902DAAC - Verified OK
.
.
.
.
Downloading 4096 bytes @ address 0x1906CAAC - Verified OK
Downloading 4096 bytes @ address 0x1906DAAC - Verify failed

.
.
.
Downloading 4096 bytes @ address 0x19104AAC - Verify failed
Downloading 4096 bytes @ address 0x19105AAC - Verified OK
.
.
.
.
Downloading 4096 bytes @ address 0x19144AAC - Verified OK
Downloading 4096 bytes @ address 0x19145AAC - Verify failed
Downloading 4096 bytes @ address 0x19146AAC - Verify failed
Downloading 2332 bytes @ address 0x19147AAC - Verify failed
Downloading 616 bytes @ address 0x191483C8 - Verify failed
Downloading 4096 bytes @ address 0x19300000 - Verify failed
Downloading 2752 bytes @ address 0x19301000 - Verify failed
Downloading 752 bytes @ address 0x3E400000 - Verified OK
Downloading 400 bytes @ address 0x3E401500 - Verified OK
Writing register (PC = 0x58690119)
Read 4 bytes @ address 0x19016958 (Data = 0xFFFFFFFF)
Resetting target
Halting target CPU...
...Target halted (PC = 0x1840494C)
Read 2 bytes @ address 0x190134EC (Data = 0xFFFF)
Read 2 bytes @ address 0x190134EC (Data = 0xFFFF)
Read 2 bytes @ address 0x190134EC (Data = 0xFFFF)
R0 = 00000004, R1 = 00000001, R2 = 00000000, R3 = 00000000
R4 = 00000001, R5 = 3E00026C, R6 = 00000000, R7 = 00000000
R8 = 00000000, R9 = 00000000, R10= 00000000, R11= 00000000
R12= 00000000, R13= 3E0001EC, MSP= 3E0001EC, PSP= 00000000
R14(LR) = 1840494D, R15(PC) = 1840494C
XPSR 61000000, APSR 60000000, EPSR 01000000, IPSR 00000000
CFBP 00000000, CONTROL 00, FAULTMASK 00, BASEPRI 00, PRIMASK 00
Reading all registers
Read 4 bytes @ address 0x1840494C (Data = 0xD0062801)
Setting breakpoint @ address 0x190134EC, Size = 2, BPHandle = 0x0001
Starting target CPU...
ERROR: Can not read register 15 (R15) while CPU is running
Reading all registers
ERROR: Can not read register 0 (R0) while CPU is running
ERROR: Can not read register 1 (R1) while CPU is running
ERROR: Can not read register 2 (R2) while CPU is running
ERROR: Can not read register 3 (R3) while CPU is running
ERROR: Can not read register 4 (R4) while CPU is running
ERROR: Can not read register 5 (R5) while CPU is running
ERROR: Can not read register 6 (R6) while CPU is running
ERROR: Can not read register 7 (R7) while CPU is running
ERROR: Can not read register 8 (R8) while CPU is running
ERROR: Can not read register 9 (R9) while CPU is running
ERROR: Can not read register 10 (R10) while CPU is running
ERROR: Can not read register 11 (R11) while CPU is running
ERROR: Can not read register 12 (R12) while CPU is running
ERROR: Can not read register 13 (R13) while CPU is running
ERROR: Can not read register 14 (R14) while CPU is running
ERROR: Can not read register 15 (R15) while CPU is running
ERROR: Can not read register 16 (XPSR) while CPU is running
ERROR: Can not read register 17 (MSP) while CPU is running
ERROR: Can not read register 18 (PSP) while CPU is running
ERROR: Can not read register 24 (PRIMASK) while CPU is running
ERROR: Can not read register 25 (BASEPRI) while CPU is running
ERROR: Can not read register 26 (FAULTMASK) while CPU is running
ERROR: Can not read register 27 (CONTROL) while CPU is running
ERROR: Can not read register 32 (FPSCR) while CPU is running
ERROR: Can not read register 33 (FPS0) while CPU is running
ERROR: Can not read register 34 (FPS1) while CPU is running
ERROR: Can not read register 35 (FPS2) while CPU is running
ERROR: Can not read register 36 (FPS3) while CPU is running
ERROR: Can not read register 37 (FPS4) while CPU is running
ERROR: Can not read register 38 (FPS5) while CPU is running
ERROR: Can not read register 39 (FPS6) while CPU is running
ERROR: Can not read register 40 (FPS7) while CPU is running
ERROR: Can not read register 41 (FPS8) while CPU is running
ERROR: Can not read register 42 (FPS9) while CPU is running
ERROR: Can not read register 43 (FPS10) while CPU is running
ERROR: Can not read register 44 (FPS11) while CPU is running
ERROR: Can not read register 45 (FPS12) while CPU is running
ERROR: Can not read register 46 (FPS13) while CPU is running
ERROR: Can not read register 47 (FPS14) while CPU is running
ERROR: Can not read register 48 (FPS15) while CPU is running
ERROR: Can not read register 49 (FPS16) while CPU is running
ERROR: Can not read register 50 (FPS17) while CPU is running
ERROR: Can not read register 51 (FPS18) while CPU is running
ERROR: Can not read register 52 (FPS19) while CPU is running
ERROR: Can not read register 53 (FPS20) while CPU is running
ERROR: Can not read register 54 (FPS21) while CPU is running
ERROR: Can not read register 55 (FPS22) while CPU is running
ERROR: Can not read register 56 (FPS23) while CPU is running
ERROR: Can not read register 57 (FPS24) while CPU is running
ERROR: Can not read register 58 (FPS25) while CPU is running
ERROR: Can not read register 59 (FPS26) while CPU is running
ERROR: Can not read register 60 (FPS27) while CPU is running
ERROR: Can not read register 61 (FPS28) while CPU is running
ERROR: Can not read register 62 (FPS29) while CPU is running
ERROR: Can not read register 63 (FPS30) while CPU is running
ERROR: Can not read register 64 (FPS31) while CPU is running
WARNING: Failed to read memory @ address 0x00000000
Removing breakpoint @ address 0x190134EC, Size = 2
WARNING: Failed to read memory @ address 0x00000000
"

SEGGER - Niklas

Super Moderator

Date of registration: Oct 6th 2014

Posts: 1,422

2

Friday, June 2nd 2017, 2:29pm

Hi Asad,


could you please answer the questions I asked you in the first thread?

Quoted

Hi Asad,


as you mentioned, the MCU is not listed as supported.
We will reach out to NXP if they can provide us with an eval board.


In the mean time, could you please provide us with a screenshot of the complete J-Link Commander output?
To which core are you trying to connect?



Best regards,
Niklas
Would you like to be added to the J-Link software update notification list, so you get informed automatically when a new version becomes available?
Just write me a PM or in case you want to subscribe to it yourself, please use this link: Link
Notification for J-Link, J-Link Debugger, SystemView & J-Scope: Link
Notification for Embedded Studio: Link

Asadloa

Beginner

Date of registration: May 26th 2017

Posts: 5

3

Saturday, June 3rd 2017, 6:47am

The problem in the old post has been solved, thanks to your answer on some one else's post.

HI Niklas,
Thanks for the response. And I am sorry, I didn't follow my last thread since the old problem has been solved, though I should mention it over there, which I will soon. The problem that I was having when I initiated the other thread was that the J-Link was unable to connect to the target, and now it does connect to Target thanks to the JScript file uploaded by you (SEGGER - Niklas) on an other thread. Now I have come further ahead as connection to target is no more an issue, but now the problem is with "reading the registers" while debigging with S32, as shown in the first post of this thread. Now I have attached the screenshots as asked by you from the J-Link Commander window when I try to connect to CORTEX M4 of MAC57D5, One is with the JScript file added and the others are without it of which 1 with SWD and the other with JTAG connection.
Best Regards,
Asad
Asadloa has attached the following images:
  • JScript.png
  • WO_JScript_SWD.png
  • WO_JScript_JTAG.png

This post has been edited 1 times, last edit by "Asadloa" (Jun 3rd 2017, 6:48am)


SEGGER - Niklas

Super Moderator

Date of registration: Oct 6th 2014

Posts: 1,422

4

Wednesday, June 7th 2017, 2:48pm

Hi,


the first screenshot looks good so far.
Do the commands go / halt / regs work in J-Link Commander?
What command line parameter do you use for J-Link GDBServer?


Best regards,
Niklas
Would you like to be added to the J-Link software update notification list, so you get informed automatically when a new version becomes available?
Just write me a PM or in case you want to subscribe to it yourself, please use this link: Link
Notification for J-Link, J-Link Debugger, SystemView & J-Scope: Link
Notification for Embedded Studio: Link

Asadloa

Beginner

Date of registration: May 26th 2017

Posts: 5

5

Saturday, June 10th 2017, 7:49am

MAC57D5, J-Link

Dear Niklas,
Thanks for the response, the first screenshot is the one with JLinkScript file added, while the other two are the ones taken prior to adding the JLinkScript file.
Now I have tried the commands that you asked me to, and I guess they are working as they should, but anyway I am attaching the screenshot of them working. Also I tried GDB server and added the screenshot for it too. I am clueless beyond this point, Please help. If segger could add support for the device, it would be mighty helpful.
Thanks
Best Regards
Asad
Asadloa has attached the following images:
  • halt_regs_go.png
  • GDBServer.png

This post has been edited 1 times, last edit by "Asadloa" (Jun 10th 2017, 7:50am)


SEGGER - Niklas

Super Moderator

Date of registration: Oct 6th 2014

Posts: 1,422

6

Monday, June 12th 2017, 9:37am

Hi Asad,


Well, it is working with J-Link Commander, so you just need to to pass the scriptfile to the GDB server aswell, and it will work in GDB Server.
In order to pass the scriptfile to gdbserver, just start it with JLinkGDBServer.exe -jlinkscriptfile $PATH_TO_SCRIPTFILE .


Best regards,
Niklas
Would you like to be added to the J-Link software update notification list, so you get informed automatically when a new version becomes available?
Just write me a PM or in case you want to subscribe to it yourself, please use this link: Link
Notification for J-Link, J-Link Debugger, SystemView & J-Scope: Link
Notification for Embedded Studio: Link

Asadloa

Beginner

Date of registration: May 26th 2017

Posts: 5

7

Thursday, June 15th 2017, 1:32pm

GDBServer not connecting

Hi Niklas,
Again, I am grateful for your response. I tried the command "JLinkGDBServer.exe -jlinkscriptfile $(I added the path to the scriptfile)" as asked by you, but I will have to say that it is not working either. The result has been attached as screenshot, it has not been able to connect to GDB server.
If you can offer any help, It will be greatly appreciated.
Regards
Asad
Asadloa has attached the following images:
  • 1.png
  • 2.png

SEGGER - Niklas

Super Moderator

Date of registration: Oct 6th 2014

Posts: 1,422

8

Friday, June 16th 2017, 9:05am

Hi,


could you please give GDBServerCl.exe a try?
If it does not work, could you please provide us the complete output of both the GDB Server as well as the GDB Client?


Best regards,
Niklas
Would you like to be added to the J-Link software update notification list, so you get informed automatically when a new version becomes available?
Just write me a PM or in case you want to subscribe to it yourself, please use this link: Link
Notification for J-Link, J-Link Debugger, SystemView & J-Scope: Link
Notification for Embedded Studio: Link